Initial checkin from CRI-O repo

Signed-off-by: Matthew Heon <matthew.heon@gmail.com>

1 files changed, 72 insertions, 0 deletions

diff --git a/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go b/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go
new file mode 100644
index 000000000..ccdb228e1
--- /dev/null
+++ b/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go
@@ -0,0 +1,72 @@
+package configs
+
+// Network defines configuration for a container's networking stack
+//
+// The network configuration can be omitted from a container causing the
+// container to be setup with the host's networking stack
+type Network struct {
+	// Type sets the networks type, commonly veth and loopback
+	Type string `json:"type"`
+
+	// Name of the network interface
+	Name string `json:"name"`
+
+	// The bridge to use.
+	Bridge string `json:"bridge"`
+
+	// MacAddress contains the MAC address to set on the network interface
+	MacAddress string `json:"mac_address"`
+
+	// Address contains the IPv4 and mask to set on the network interface
+	Address string `json:"address"`
+
+	// Gateway sets the gateway address that is used as the default for the interface
+	Gateway string `json:"gateway"`
+
+	// IPv6Address contains the IPv6 and mask to set on the network interface
+	IPv6Address string `json:"ipv6_address"`
+
+	// IPv6Gateway sets the ipv6 gateway address that is used as the default for the interface
+	IPv6Gateway string `json:"ipv6_gateway"`
+
+	// Mtu sets the mtu value for the interface and will be mirrored on both the host and
+	// container's interfaces if a pair is created, specifically in the case of type veth
+	// Note: This does not apply to loopback interfaces.
+	Mtu int `json:"mtu"`
+
+	// TxQueueLen sets the tx_queuelen value for the interface and will be mirrored on both the host and
+	// container's interfaces if a pair is created, specifically in the case of type veth
+	// Note: This does not apply to loopback interfaces.
+	TxQueueLen int `json:"txqueuelen"`
+
+	// HostInterfaceName is a unique name of a veth pair that resides on in the host interface of the
+	// container.
+	HostInterfaceName string `json:"host_interface_name"`
+
+	// HairpinMode specifies if hairpin NAT should be enabled on the virtual interface
+	// bridge port in the case of type veth
+	// Note: This is unsupported on some systems.
+	// Note: This does not apply to loopback interfaces.
+	HairpinMode bool `json:"hairpin_mode"`
+}
+
+// Routes can be specified to create entries in the route table as the container is started
+//
+// All of destination, source, and gateway should be either IPv4 or IPv6.
+// One of the three options must be present, and omitted entries will use their
+// IP family default for the route table.  For IPv4 for example, setting the
+// gateway to 1.2.3.4 and the interface to eth0 will set up a standard
+// destination of 0.0.0.0(or *) when viewed in the route table.
+type Route struct {
+	// Sets the destination and mask, should be a CIDR.  Accepts IPv4 and IPv6
+	Destination string `json:"destination"`
+
+	// Sets the source and mask, should be a CIDR.  Accepts IPv4 and IPv6
+	Source string `json:"source"`
+
+	// Sets the gateway.  Accepts IPv4 and IPv6
+	Gateway string `json:"gateway"`
+
+	// The device to set this route up for, for example: eth0
+	InterfaceName string `json:"interface_name"`
+}